Шэньчжэньская компания cumrun Power Technology Co., Ltd.
Язык
EnglishEspañolFrançaisالعربيةРусский

Двигатель насоса Cummins KTA50-P2220 1656 кВт при 1800 об/мин

» Двигатель насоса Cummins » Cummins KTA50-P2220 1656kw@1800rpm Pump Engine

Двигатель насоса Cummins KTA50-P2220 1656 кВт при 1800 об/мин

КАТЕГОРИИ И ТЕГИ:
Двигатель насоса Cummins
Скачатьрасследование
  • Технические характеристики

Двигатель насоса Cummins KTA50-P2220 1656 кВт при 1800 об/мин

Скорость двигателя Standby Power Prime Power Continuous Power
об/мин kWm BHP kWm BHP kWm BHP
1800 1656 2220 1384 1855 1224 1640

Emissions Certification

This engine complies with certain emissions requirements established by US EPA/CARB. See Exhaust Emissions Data Sheet for conformance specifics.

Engine Performance Data @ 1800 об/мин

U.S. Gallons/hour

OUTPUT POWER FUEL CONSUMPTION
% kWm BHP kg/

kWm-h

lb/

BHPh

liter/

hour

U.S. Gal/ hour
STANDBY POWER
100 1656 2220 0.201 0.331 392 103.6
PRIME POWER
100 1384 1855 0.203 0.334 330 87.3
75 1038 1391 0.211 0.347 257 68.0
50 692 928 0.221 0.364 180 47.6
25 346 463 0.273 0.449 111 29.2
CONTINUOUS POWER
100 1224 1640 0.208 0.342 299 79.0

GENERAL ENGINE DATA
Тип………………………………………………………….4-Cycle; 60° Vee; 16-Cylinder Diesel
Стремление…………………………………………………. с турбонаддувом & Low Temp. После охлаждения
Bore x Stroke …………………………………………….— in x in (mm x mm) 6.25 x 6.25 (159 x 159)
Смещение …………………………………………….— in3 (liter) 3067 (50.3)
Compression Ratio……………………………………….13.9 : 1
Dry Weight
Fan to Flywheel Engine…………………………………… — lb (kg) 11820 (5360)
Wet Weight
Fan to Flywheel Engine…………………………………. — lb (kg) 12485 (5662)
Moment of Inertia of Rotating Components
• with FW 6009 Flywheel ………………………………..— lbm • ft2 (kg • m2) 301 (12.7)
• with FW 6017 Flywheel…………………………………… — lbm • ft2 (kg • m2) 515 (21.7)
Center of Gravity from Rear Face of Flywheel Housing (FH 6024)………………………………….. — in (мм) 47.5 (1206)
Center of Gravity above Crankshaft Centerline……………………………………………………………… — in (мм) 11.0 (279)
Maximum Static Loading at Rear Main Bearing………………………………………………………………. — lb (kg) 2000 (908)
ENGINE MOUNTING
Maximum Bending Moment at Rear Face of Block……………… — lb • ft (N • m) 4500 (6100)
EXHAUST SYSTEM
Maximum Back Pressure @ Standby Power Rating ……………….. — in Hg (mm Hg) 2 (51)
AIR INDUCTION SYSTEM
Maximum Intake Air Restriction
• with Dirty Filter Element @ Standby Power Rating………….. — in H2O (mm H2O) 25 (635)
• with Clean Filter Element @ Standby Power Rating………………. — in H2O (mm H2O) 15 (381)
COOLING SYSTEM (Low Temperature Aftercooling Required; 1 Pump / 2 Loop or 2 Pump / 2 Loop)
Coolant Capacity — Engine Only………………………………………………— US gal (liter) 37 (140)
— Aftercoolers……………………………………………………………………… — US gal (liter) 9 (34)
Maximum Static Head of Coolant Above Engine Crank Centerline…………………………………….. — ft (m) 60 (18.3)
Thermostat Modulating Range — High Flow (Jacket) …………….. —°F (°C) 180 – 200 (82 – 93)
Maximum Top Tank Temperature for Standby Power / Prime Power………………………………. —°F (°C) 220 / 212 (104 / 100)
Target Coolant Inlet Temperature to Aftercoolers @ 77 °F (25 °C) Ambient— ……………………. °F (°C) 130 (55)
Maximum Coolant Temperature to Aftercoolers; Standby Power / Prime Power ………………—°F (°C) 160 / 150 (71 / 66)
Additional 2 Pump / 2 Loop Requirements
Maximum Coolant Friction Head External to Engine— High Flow (Jacket)……………….— psi (kPa) 10 (67)
— Low Flow (Aftercooler)………………………………— psi (kPa) 7 (48)
Thermostat Modulating Range — Low Flow (Aftercooler) (2P / 2л) w/ HX ____. —°F (°C) N.A. (N.A.)
Minimum Pressure Cap (for Cooling Systems with less than 2 m [6 ft.] Static Head)… — psi (kPa) 14 (96)
Additional 1 Pump / 2 Loop Requirements
Maximum Coolant Friction Head External to Engine— High Flow (Jacket) ……………….— psi (kPa) 15 (103)
— Low Flow (Aftercooler)………………………………— psi (kPa) 5 (35)
Thermostat Modulating Range — Low Flow (Aftercooler)………………………………. —°F (°C) 150 – 175 (66 – 79)
Minimum Pressure Cap (for Cooling Systems with less than 2 m [6 ft.] Static Head)… — psi (kPa) 14 (96)
LUBRICATION SYSTEM
Oil Pressure @ Idle Speed………………………………………………. — psi (kPa) 20 (138)
@ Governed Speed………………………………………………………….— psi (kPa) 50 – 70 (345 – 483)
Maximum Oil Temperature ……………………………………………. —°F (°C) 250 (121)
Oil Capacity with OP 6027 Oil Pan : HighLow……………….. — US gal (liter) 47 – 39 (178 – 148)
Total System Capacity (Including Bypass Filter) ………………. — US gal (liter) 54 (204)
FUEL SYSTEM
Type Injection System………………………………………………………Direct Injection Cummins PT
Maximum Restriction at PT Fuel Injection Pump — with Clean Fuel Filter……………………………………………. — in Hg (mm Hg) 4.0 (102)
— with Dirty Fuel Filter……………………………………………… — in Hg (mm Hg) 8.0 (203)
Maximum Allowable Head on Injector Return Line (Consisting of Friction Head and Static Head)…………. — in Hg (mm Hg) 6.5 (165)
Maximum Fuel Flow to Injection Pump…………………………………..— US gph (liter / hr) 183 (693)
ELECTRICAL SYSTEM
Cranking Motor (Heavy Duty, Positive Engagement)………………………………………………………………………. — volt 24
Battery Charging System, Negative Ground…………………………………………………………………………………………………. — ampere 35
Maximum Allowable Resistance of Cranking Circuit ………………………………..— ohm 0.002
Minimum Recommended Battery Capacity
• Cold Soak @ 50 °F (10 °C) and Above………………………………………… — 0°F CCA 1280
• Cold Soak @ 32 °F to 50 °F (0 °C to 10 °C) …………………………………… — 0°F CCA 1800
• Cold Soak @ 0 °F to 32 °F (-18 °C to 0 °C) ………………………………………… — 0°F CCA 1800
COLD START CAPABILITY
Minimum Ambient Temperature for Aided (with Coolant Heater) Cold Start within 10 seconds…………………………. —°F (°C) 50 (10)
Minimum Ambient Temperature for Unaided Cold Start …………………………—°F (°C) 45 (7)
PERFORMANCE DATA
All data is based on: • Engine operating with fuel system, water pump, lubricating oil pump, air cleaner and exhaust
silencer; not included are battery charging alternator, fan, and optional driven components.
• Engine operating with fuel corresponding to grade No. 2-D per ASTM D975.
• ISO 3046, Part 1, Standard Reference Conditions of:
Barometric Pressure : 100 kPa (29.53 in Hg) Air Temperature : 25 °C (77 °F)
Altitude : 110 m (361 ft) Relative Humidity : 30%
Steady State Stability Band at any Constant Load …………………………………………………………………. % +/- 0.25
Estimated Free Field Sound Pressure Level of a Typical Generator Set;
Excludes Exhaust Noise; at Rated Load and 7.5 m (24.6 ft); 1800 об/мин……………………………………………………….. — dBA 94.6
Exhaust Noise at 1 m Horizontally from Centerline of Exhaust Pipe Outlet Upwards at 45°………………………………….. — dBA 130

The above is general technicial information of Cummins KTA50-P2220 Pump Engine. It is also for us to supply the Cummins KTA50-P2220 genuine parts and KTA50-P2220 engine units with water pump(Fire pump)

Двигатель насоса Cummins,Силовые агрегаты Камминз,Морские силовые агрегаты Cummins,Пожарная машина Камминс,Взрывозащищенный двигатель Cummins,Дилер насосных двигателей Cummins,Средство для насосных двигателей Cummins

Форма запроса ( мы свяжемся с вами как можно скорее )

Имя:
*
Электронная почта:
*
Сообщение:

Проверка:
3 + 8 "=" ?

Возможно, вам также понравится

  • Двигатель насоса Cummins,Силовые агрегаты Камминз,Морские силовые агрегаты Cummins,Пожарная машина Камминс,Взрывозащищенный двигатель Cummins,Дилер насосных двигателей Cummins,Средство для насосных двигателей Cummins XML